5 kV AC, 6 kV DC Hipot + IR Tester DC Hipot Testers DPC series Udey Test Kits

Hipot Testers DPC series : UDEY TESTER-US-56I is microprocessor controlled AC/DC Hipot with Insulation Resistance Tester. US-561 is designed to perform high voltage withstand and insulation resistance tests on various types of electrical products, systems and components.

Machine Feature

• AC/DC withstand tests and Insulation resistance tests.
  • IR test mode: IR can be performed independently or in sequence with Dielectric Withstand test.
  • User selectable output voltage frequency of 50 Hz or 60 Hz.
  • Setup of trip current and output voltage without the high voltage activated.
  • Store and Recall test set-up memories.
  • All parameters are set up through simple menu driven program on screen.
  • Line load regulation from no load to full load.
  • Front ‘Keys’ can be locked providing limited user access so that only authorized personnel with unlock code can modify test parameters.
  • Backlit LCD display allows monitoring of 100uA AC and 20uA DC: Useful when test requirements only allow a very low level of acceptable leakage current.
  • Advance A/D conversion, Uses ‘Digital frequency synthesis’ technology to achieve perfect AC test power with crest factor of 1.35-1.45
  • Electronic settings: ‘Test Voltage’, ‘High / Low limits of current’, ‘Ramp up time’, ‘Dwell time’.
  • Backlit LCM display
  • Indicators: Flashing ‘HV ON’, ‘PASS’ and ‘FAIL’ indicators.
  • ‘Audio’ alarm at ‘FAIL’.
  • Maximum output current is 12mA AC and 6mA DC.
  • Remote output for control to configure tester through simple PLC relay control.
  • Rugged table top cabinet

 

Machine Technical Specification

Supply Voltage	115/230 Volts ± 10%AC, 47-63 Hz single Phase.
AC WITH STAND TEST
Output Test Voltage	Nominal : 0-5kV/12mA AC
Output Frequency	50 Hz / 60 Hz
Output Waveform	Sine wave THD : <2% [Crest Factor > 1.3<1.5]
TRIP : Upper Limit	0.10 to 12.00mA; Resolution: 0.01mA per step Accuracy: ± 2% + 2 counts [0.01 to 11mA]
DC WITH STAND TEST
Output Test Voltage	Nominal: 0-6kV/5mA DC
Output Ripple:mV p-p	<5% at 6kV/5mA Under Resistive Load
TRIP : Upper Limit	0.02 to 5.00mA; [0=OFF]. Resolution: 0.01mA per step Accuracy: ± 2% + 2 counts [0.01 to 11mA)
TRIP : Lower Limit	0.00 to 5.00mA; [0=OFF]. Resolution: 0.01mA per step Accuracy: ± 2% + 2 counts [0 to 4mA)
Voltage Setting AC/DC	AC : 0.00 to 5.00kV DC : 0.00 to 6.00kV Resolution : 0.01kV per step; Accuracy: ±2% + 5 Volts. Can be adjusted during test by UP/DOWN Keys
Voltage Regulation	± 1% + 5 volts [No load to full load].
Ramp Time [ Rise Time] DWELL TIME [Test time]	0.1 to 999.9 seconds, 0.1 second per step 0=0.1 second fixed setting 0.2 to 999.9 seconds, 0.1 second per step 0=Continuous running
METERING : 4 digits Voltmeter AC/DC	AC: 0.00 to 5.00kV; DC: 0.00-6.00kV Resolution: 0.01kV; Accuracy:± 2% + 1 count.
Ammeter AC/DC Timer	AC: 0.10 to 12.00mA; DC: 0.02-5.00mA Resolution: 0.01mA; Accuracy: ± 2% + 1 count. Range: 0.0 to 999.9 seconds; Resolution: 0.1 second. Accuracy: ± 0.1% reading + 0.05 seconds.
INSULATION RESISTANCE TEST Test Voltage : Settable	0.01 to 1.00kV DC; Resolution: 0.1kV per step Accuracy: ± 2% + 2 volts.
Test Voltage : Display	0.00 to 1.00kV DC; Resolution: 0.01kV per step Accuracy: ± 2% + 1 count.
Resistance : Display	1 to 1000 Meg ohm Accuracy : ± 5% + 2 count at voltage = 500V DC. ± 7% + 2 count at voltage = 500V DC.
Test Time Resistance : Upper Limit Resistance : Lower Limit	0.5 to 999.9 seconds, 0.1 s per step 0 = Continuous; Accuracy: ± 0.1% + 0.05 s. 0 and 1 to 1000 Meg ohm [0=OFF] Resolution : 1 Meg ohm per step Accuracy : ± 5% + 2 count at voltage = 500V DC. : ± 7% + 2 count at voltage = 500V DC. 1 to 1000 Meg ohm; Resolution : 1Meg ohm per step Accuracy : ± 5% + 2 count at voltage = 500 V DC. : ± 7% + 2 count at voltage = 500 V DC. GENERAL
Remote Control + Signal Failure Alarms Auto Discharge	9 pin ‘D’ socket provides the following signals: a) Remote Control : Test, Reset, Interlock b) Outputs : Pass, Fail, Test in progress Buzzer, LCD Display, Indicator Maximum 200 ms Maximum capacitive load verses output voltage 0.2 uF : Maximum 1kV 0.1 uF : Maximum 2kV 0.05 uF : Maximum 4kV 0.04 uF : Maximum 5kV 0.015 uF : Maximum 6kV
Program Memory	5 memories, 4 test modes selectable [W, I, W-I, I-W]
Keyboard Lock	Key Lock to avoid unauthorized access of use.
Display	LCD, dot matrix, back lit
Construction Power Cord	Sheet Steel Table Top Cabinet, Powder Coated with tilt-up front Feet. Detachable 2 meter long powder cord terminated in 3 pin grounding plug.
Use Environment	Temperature : 0-40 deg C; R.H. = Maximum 80% Altitude : Max 2000 Meters.
Dimensions	W x D x H : 28 x 39 x 9 cm approximately. 9 kg approximately

 

Standard Accessories

1. a) Mains cord 2 meter long – 1 Number
   b) HV and RETURN Test Leads – 1 Set
   c) D Connector with cable – 1 Number

Explore the comprehensive range of Udey test kits click here!